Are you experiencing hydraulic problems with your cat 279c? If you are reading this, then most likely you have had some problems with the hydraulics of your machine. In this article, we will discuss some of the most popular issues which occur in hydraulic system and their remedies as well.
Leaking Cat 279C hydraulic lines
If you have any problem with your Cat 279C hydraulic line or other hydraulic lines, fixing the problem can be done by following some simple steps. Here are a few things that you can do to fix hydraulic leaks:
1.Inspect the seals and gaskets on the line. Sometimes, bad seals and gaskets can cause leaks. If you cannot spot any visible problems, then replace the seals and gaskets.
2.Check for blockage in the lines. Hydraulic lines sometimes catch debris thus leading to leakages. Use a tube of compressed air or vacuum cleaner to remove any obstructions.
3.Remove foreign bodies causing obstruction. Hydraulic leaks could be caused by broken equipment, stones or other debris. They should be removed using a tube of compressed air or hand held vacuum cleaner.
4.Look for damage on the pipe itself – If it appears to have been damaged; it may need replacing completely. Such damages come in form of metal line tears, cuts and cracks in it .
Cat 279C Hydraulic problems with a hydrostatic transmission
In the event that you experience problems with your hydraulic transmission of Cat 279C, it is crucial to troubleshoot and find out what the problem is. Below are some hints to get you started.
1.Inspect fluid level
Among the first things that should be done if having a difficulty with your cat 279C hydraulic transmission is inspecting its fluid level. Make sure that there exists no debris or contamination in the system and that the fluid level is okay.
2.Identifying leaks
If you have checked and found nothing wrong with your fluid levels, then checking for any leakages would be the next step. The failure of these systems to work optimally can therefore be attributed to such leaks.Leaks can come up from all around the system including pump, seals and valves.
3.Examine pump and seals
Should there be no leakage yet correct fluid level then examine pump and seals. The reason behind this could be a failed pump causing low levels of fluid or even complete breakdown of transmission process. Check for wear (including cracks in housing), damage, contamination on pumps; check for cracks, tears, contamination in seals as well.
4.Replace worn out components
When some parts of yourCat 279C hydraulic transmission begin wearing off or breaking down it may mean replacing them back afresh so as to make it run like before again.This will return it to its original state hence functioning properly again as desired.
Cat 279C Loader arms are slow to respond
In case of Cat C hydraulic arm showing some malfunction, there are few things you can do to rectify the problem.
1.Proper lubrication of hydraulics should be done. If the arm doesn’t move freely, there may be areas that oil cannot reach in the entire system.
2.Ensure all cables are firm enough. They may cause improper movement of an arm if they are not tight.
3.Check if there is something blocking the line in the hydraulic system. When there is such a thing as obstruction it could probably make an arm move sluggishly or not at all.
Boom Cat 279C Hydraulic pump is slow to respond
When your Boom Cat 279C hydraulic pump is not responding as it should, there are certain things that can be done. Hydraulic pumps problems may result from different factors; therefore, it is important to identify the problem and find a solution rather than coming up with some radical measures.
Below are the most common causes of slow response of Boom Cat 279C hydraulic pump:
1.Broken or blocked pipes: The first thing you will do when you realize that your Boom Cat 279C hydraulic pump is slow in reacting is to inspect the pipes that connect the pump to the tank or reservoir. In case these lines are broken or blocked, then energy transfer between the reservoir and engine becomes difficult for the pump.
2.Low oil level: If there is little oil in your tank; this means that there will be no enough energy for starting an engine. Always check oil levels regularly so as to fill up if necessary.
3.Malfunctioning valves: When one or more valves on a boomcat279chydraulic pump become faulty, they may not assist in transferring all energy required by an engine from its reservoir properly thus leading to delayed response time.
4.A bad motor: Your Boom Cat 279Chydraulic pump might have a motor failure such that it cannot provide the needed force required for moving the device. This can cause a slow response time.
If after doing all these you still experience problems with your Boom Cat 279C hydraulic pump, it’s better you take it for repair or replacement services. Just visit our office and get help from skilled experts in repairing machines like yours if unsure about what done into yours..
Cat 279C Bucket tilt is slow to respond
If at all the bucket tilt of your Cat 279C is giving you problems, there are some things that you can try to correct it.
Firstly, ensure that the hydraulics are performing properly. Ensure that oil is freely flowing out from the valve and gearbox is rotating smoothly. If the hydraulics are not working properly, they may need servicing.
Despite proper functioning of the hydraulics, slow response time may be experienced. Worn gears or bearings are some of what might cause this. In such a case, you may have to replace some parts of the mechanism.
Cat 279C Hydraulic faulty wiring may be an issue
Possibly, the problems of the machine may be due to incorrect wiring. This faulty wiring can result in the hydraulic system becoming inoperative or malfunctioning.
To respond, if you experience this kind of issues with your machine, do something about it. We have a manual which gives steps you can follow to troubleshoot the problem by yourself. Or else, you can hire a mechanic to come and inspect then repair it.
However, whichever option you go for, ensure that you are careful and get advice from an expert technician before doing anything. If there are no actions taken soon, this machine will be destroyed eventually.
Cat 279C Hydraulic fluid level too low
If your Cat 279C hydraulic fluid level is not correct, then here are some solutions to help you get it back on track.
1.Check the oil level and verify that it is at the right mark on the dipstick. The engine’s oil levels may change over time and thus require some amendment. Observe the manufacturer’s instructions on changing of oils.
2.Ensure that there are no other sediments or materials in the hydraulic system. For example, eliminate any foreign objects which may be obstructing lines or pipes and wipe them out using solvent like acetone or petroleum jelly.
3.Make sure all hoses are straight without twistings and kinks prior to installing again.
4.Inspect all seals as well as gaskets for signs of wear and tear or damage Replace damaged gaskets or seals when necessary
5.Flush out hydraulic fluid at least once every year or after a travel distance of 10,000 miles whichever occurs first (or as specified in your owner’s manual). Look up flushing instructions in your owner’s manual
Cat 279C Hydraulic Undercarriage does not work properly
If things does not work properly for your Cat 279C hydraulic undercarriage, there are few things you can try out to troubleshoot the problem.
1.Check the fluid level
Firstly, look at the level of fluid in the hydraulic system. Ensure that it is more than half full if not you may have to replace the whole hydraulic system.
2.Inspect the gears
If they are not moving correctly, then they might be damaged hence you will need to change them.
3.Inspect the transmission system
It could be a broken seal or perhaps worn gear causing a malfunctioning transmission system. Hence replace damaged parts with new ones instead of fixing single item in it.
Oil leak at the Cat 279C travel motor
If you have a hydraulic problem on your Cat 279C travel motor, there are some things that you can do to solve the issue. Here are some tips to assist you in troubleshooting and fixing oil leaks as given below:
1.Check the oil levels. Ensure the oil is at the right level by checking dipsticks. To increase the oil amount for your motor, add more fuel.
2.Check for any loose parts. If there are loose parts in your hydraulic system, they can cause leaks. Replace all loose parts that have been identified and try repairing the leak with a Hydraulic Tube Repair Kit or any other Hydraulic Fix Kit.
3.Check if it’s clogs or debris causing it. Clogs or debris within the hydraulic system will also contribute to this leakage condition happening due to these materials too.Clean up all clogs and debris using Hydraulic Filter Fluid or a Hydraulic Cleaner .
4.Check if there is blocked pipes anywhere else . Blocked pipes in gears would also lead to such leakages .Remove all obstacles using Hydraulic Pump Cleaner or Pipe-Sealant .
Cat 279C Hydraulic is required, click to ask for price
Cat 279C Track coming off the sprocket
If your Cat C Hydraulic Track is coming off the sprocket, here is what you can do:
1.Ensure that the track of the crawler machine is well adjusted to stay close on the hub. The reason behind this is that loose tracks interferes with its position and as a result it may be pulled away.
2.You will need to inspect both the crawler track as well as the drive sprocket for any signs of damage during operation. This may include excessive wear or deformation, which causes loss of contact between them.
3.Replace worn out parts. After long use, these parts wear out and therefore are not able to provide necessary traction for proper running.
Summarize
The leak is one of the most widespread challenges that hydraulic systems face, where the fluid that propels it finds an escape route causing harm.
There may be a number of ways to rectify hydraulic leaks. For instance, the easiest and probably the most frequent solution is buying and installing new damaged part which can be very expensive. However, another way is sealing up the affected area. This will stop the spillage of fluid and so limit the damage.
Related Reading
CAT Hydraulic Pump Troubleshooting Guide
Cat 416 Hydraulic Problems And Solutions
English
Russian
French
German
Portuguese
Spanish